Getting Started with Plumber's Essentials for Bathtub Installation
Getting Started with Plumber's Essentials for Bathtub Installation
Blog Article
On this page down the page yow will discover lots of really good tips around How to Install a Bathtub Yourself.
Mounting a bath tub isn't specifically rocket science, but it does require solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a reasonably hard task. If the old bathtub is easily accessible, the project can move quickly; if you have to open up a wall surface to get rid of the old bathtub as well as position the new bath tub, the job is a lot harder. In either case, the task is within a residence handyman's abilities, although you will require a helper to vacate the old bathtub and set in the brand-new one. Ensure you have actually qualified yourself for the work as well as fit trying it. Instead of working with a service provider to take over a halfway-completed task, it is better to think about utilizing one prior to you begin. Chances are you might require a specialist plumber to make tube connections.
This article will certainly assist you install a new bath tub in your restroom if you have actually already purchased a brand-new tub as well as do not need to change the plan of your previous water pipes.
Your tools as well as material list need to comprise the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The process of eliminating the existing taps can be rather troublesome because of the restricted gain access to that is frequently the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a fabric all set for the staying water that will originate from the pipes. Once the supply pipelines have been gotten rid of, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. Once the taps have actually been removed, the holes in the bath/basin will have to be cleansed of any old securing substance.
Before moving on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washing machines remain in place in between the faucet as well as the sink. Secure the tap in position with the maker offered backnut. Once the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical faucet adapters. The former kind ought to be linked to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Setting up the Bath tub
Using both wood boards under its feet, place the tub in the called for position. The wooden boards are handy in evenly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the bath tub till the spirit level reads degree.
To install faucets, fit all-time low of the furthest flexible faucet port to the ideal supply pipe by making a compression sign up with; then do the exact same for the other tap.
Turn on the water supply as well as examine all joints and brand-new pipework for leaks and also tighten them if required. Load the bathtub as well as likewise examine the overflow outlet as well as the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the producer's instruction manual. Tiling as well as sealing around the bathtub ought to wait until the bathtub has been made use of at the very least when as this will certainly resolve it right into its last placement.
Planning for the Setup
Firstly, the supporting structure supplied with the bath needs to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also practical to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be fitted in its last setting.
Tiling Around the Tub
In the area where the bath satisfies the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to fracture a rigid seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, leading to problems with wetness and also possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and also installations. They are sold in tubes and also cartridges, as well as are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to allow for the movement experienced when the tub remains in usage. The sealant can crack fairly early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly offered on the market. It is suggested to fit the ceramic tiles using waterproof or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very interested in A Step-by-Step Guide to Installing a Bathtub and I really hope you appreciated the new blog posting. Enjoyed reading our review? Please share it. Let other people locate it. I am grateful for your time. Kindly come by our website back soon.
Quick resolutions for plumbing disruptions. Report this page